iFixit - Answers With Device "Jura Impressa F50"

Jura Impressa F50: How to perform decalcification forcefully on Jura F50.

Sat, 01 Feb 2025 10:02:38 -0700

My water flow is very weak and I think it's due to no decalcination cycle in a long time. In instruction it says to wait for message and only then you can do it. There is no maintenance menu for separate de-scaling.

⟐ Answered February 01, 2025 at 10:02 MST

Jura Impressa F50: Jura F50 water blockage

Mon, 29 Jan 2024 01:54:09 -0700

Water is not flowing through the coffee

Jura F50. Water is not going through the coffee. Hence no cups of fresh coffee. What could be blocking the water flow?

⟐ Answer accepted January 29, 2024 at 1:54 MST

Jura Impressa F50: Water leaking behind nozzles

Thu, 18 Aug 2022 06:53:38 -0700

When trying to make coffee or espresso, the water leaks behind the nozzles and not hardly through the silver nozzles. I've cleaned the machine, no error codes, what could the problem be

⟐ Answered August 18, 2022 at 6:53 MST

Jura Impressa F50: The water flow is just a trickle

Sat, 17 Dec 2022 10:04:39 -0700

Hi, my water flow from the faucet is so slow and practically dripping taking a long time to fill a cup, I have taken it all apart and hoovered the guts, no sign of leaking, I have taken the faucet off and cleaned the tubes cos I read they can sometimes get clogged with coffee granules...it has been asking to open tap a lot and fill water when the water tank is completely full....I am at a loss

⟐ Answer edited December 17, 2022 at 10:04 MST

Jura Impressa F50: It's saying drip tray not fitted

Wed, 02 Jul 2025 02:39:26 -0700

It was pulled apart and put back together a screw was misplaced and now it's saying drip tray not fitted error, unsure where the screw went or came from just know that 1 is missing. What screws missing could cause this error directly?

⟐ Commented July 02, 2025 at 2:39 MST

Jura Impressa F50: Why does system not fill

Sat, 08 Jul 2023 00:18:59 -0700

When machine is switched on, the 'Open tap' message displays. When the tap is opened, water comes out the steam spout, the message states 'Filling system' followed by 'Close tap', and then goes to 'Open tap'

This cycle repeats itself endlessly. The flow meter impeller does turn. Not sure how to continue?

Jura Impressa F50: Jura impressa F50 the grinder runs continuously

Sat, 18 Feb 2023 08:29:11 -0700

hello, I have this coffee machine. When I connect the cable with the display off, the coffee grinder starts automatically. do you have any opinions I will also check the CI motherboard and transistors. any opinions? Thank you.

Jura Impressa F50: Dial to Control Ounce Size Not Working

Wed, 11 Jan 2023 01:51:04 -0700

The dial that controls the number of ounces dispensed turns, but the oz. quantity "flies" all over and is difficult to set to a price number. Any thoughts on the cause? It's almost like it may just need to be disassembled and contact point(s) cleaned.

Jura Impressa F50: Frequently asks to "open tap", but does not work

Wed, 06 Apr 2022 06:40:11 -0700

The machine frequently asks to "open the tap" which is normally done for cleaning or pushing out air. Only in this case, once the tap is open, nothing happens. What did most of the time help is just to let it sit for a while. When it does produce coffee, presumably pressure is also lower than before, though I cannot check/compare this.

On another forum, it was suggested that this just might be calcification, but then I would at least expect the pump to try to do some work in the cases when it asks to open the tap. But it does not even try. In addition, this error also precludes proper maintenance, for example when I did the last cleaning cycle, it did not complete properly at first because it also asked to "open the tap"/did not continue during the cleaning cycle because of not pumping water.
Any ideas which component this might be related to?

Please note: "Tap" in this case might be a bad translation, not sure what the english translation used by the manufacturer in their display is in this case.